If attach insecurely, the servo motor may come off during HC-SFS121 201HC-SFS202 352HC-SFS203 353HC-UFS202 to 502ĬAUTIONSecurely attach the servo motor to the machine.
#A VER SERIES#
HC-SFS81HC-SFS52 to 152HC-SFS53 to 153HC-RFS Series
#A VER FREE#
20 to 65 (non-freezing) 15 to 70 (non-freezing)Storagetemperature 4 to 149 (non-freezing) 5 to 158 (non-freezing)Storage humidity 90%RH or less (non-condensing)Ambience Indoors (no direct sunlight) Free from corrosive gas, flammable gas, oil mist, dust and dirtAltitude Max. 0 to 55 (non-freezing) 0 to 40 (non-freezing)Ambienttemperature 32 to 131 (non-freezing) 32 to 104 (non-freezing)Ambient humidity 90%RH or less (non-condensing) 80%RH or less (non-condensing) Isolate from all impact loads.Use the servo amplifier and servo motor under the following environmental conditions:
#A VER INSTALL#
Do not put heavy objects on equipment.The controller and servo motor must be installed in the specified direction.Leave specified clearances between the servo amplifier and control enclosure walls or other equipment.Do not install or operate the servo amplifier and servo motor which has been damaged or has any partsmissing.Provide adequate protection to prevent screws and other conductive matter, oil and other combustiblematter from entering the servo amplifier.Do not drop or strike servo amplifier or servo motor. The controller may drop.Install the servo amplifier in a load-bearing place in accordance with the Instruction Manual.Do not climb or stand on servo equipment. Incorrect handling may cause a fault, injury, electricshock, etc.ĬAUTIONTransport the products correctly according to their weights.Stacking in excess of the specified number of products is not allowed.Do not carry the motor by the cables, shaft or encoder.Do not hold the front cover to transport the controller. The following instructions should also be fully noted. may occur.ĭuring power-on or for some time after power-off, do not touch or close a parts (cable etc.) to the servoĪmplifier heat sink, regenerative brake resistor, servo motor, etc.
#A VER MANUAL#
Regenerative brake transistor fault or the like may overheat the regenerative brake resistor, causing a fire.ĬAUTIONOnly the voltage specified in the Instruction Manual should be applied to each terminal, Otherwise, aĬonnect the terminals correctly to prevent a burst, damage, etc.Įnsure that polarity (, ) is correct. When a regenerative brake resistor is used, use an alarm signal to switch main power off. Continuousįlow of a large current may cause a fire. When the servo amplifier has become faulty, switch off the main servo amplifier power side. Otherwise, you may get an electric shock.ĬAUTIONDo not install the servo amplifier, servo motor and regenerative brake resistor on or near combustibles. The cables should not be damaged, stressed, loaded, or pinched. Operate the switches with dry hand to prevent an electric shock. Otherwise, you may get an electric shock.Ĭonnect the servo amplifier and servo motor to ground.Īny person who is involved in wiring and inspection should be fully competent to do the work.ĭo not attempt to wire the servo amplifier and servo motor until they have been installed. WARNINGBefore wiring or inspection, switch power off and wait for more than 10 minutes. To prevent electric shock, note the following: In this Instruction Manual, instructions at a lower level than the above, instructions for other functions, and soĪfter reading this installation guide, always keep it accessible to the operator.ġ. What must not be done and what must be done are indicated by the following diagrammatic symbols: Instructions of both levels because they are important to personnel safety. Note that the CAUTION level may lead to a serious consequence according to conditions. Resulting in medium or slight injury to personnel or may cause physical
WARNINGIndicates that incorrect handling may cause hazardous conditions,ĬAUTIONIndicates that incorrect handling may cause hazardous conditions, In this Instruction Manual, the safety instruction levels are classified into "WARNING" and "CAUTION". Do not use the servo amplifier and servo motor until you have aįull knowledge of the equipment, safety information and instructions. Through this Instruction Manual, Installation guide, Servo motor Instruction Manual and appended documentsĬarefully and can use the equipment correctly. Safety Instructions (Always read these instructions before using the equipment.)ĭo not attempt to install, operate, maintain or inspect the servo amplifier and servo motor until you have read
0 kommentar(er)
